Canon LBP-2000 Manuel de service Page 219
- Page / 222
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
A - 15
APPENDIX
e. The following messages are displayed on the SERVICE mode.
Message
NVRAM OK
NVRAMx ERROR
WRITING NVRAMx
ERROR
CHECK NVRAM
+REALLY/-IGNORE
x -> y
+ FORMAT DISK
- IGNORE DISK
+ REALLY FORMAT
- IGNORE DISK
START DISK TEST
ENTER ENDS TEST
FORMATTING…
DSK FMT RESTART
+ FORMAT FLASH
- IGNORE FLASH
+ REALLY FORMAT
- IGNORE FLASH
FLASH FORMAT
RESTART
FLASH
FORMATTING…
+ REALLY CLEAR
- IGNORE CLEAR
DONE
FAILED
Meaning
All NVRAMs work correctly.
An error occurred in the
NVRAMx.
A writing error occurred in
the NVRAMx.
Incorrect information has
been found in the NVRAM.
Duplicate page counter
information from the
NVRAMx to the NVRAMy?
Format the printer hard
disk?
The operator is being asked
to verify the disk formatting
is really wanted. This is in
response to the foregoing
message.
Start the hard disk test?
Stop the hard disk test?
The printer hard disk is
being formatted.
The printer hard disk has
been formatted.
Format the optional Flash
ROM?
Continue formatting the
optional Flash ROM?
The optional Flash ROM has
been formatted. The printer
will restart.
The optional Flash ROM is
being formatted.
Clear the device password?
The operation of clearing a
password or error flag of
engine NVRAM has done
successfully.
The operation of clearing a
password has failed.
Action
Reinstall or replace the NVRAM.
Replace the NVRAM.
Replace the NVRAM.
Select + (press the Value key) to continue
duplication, or select - (press the Shift and
Value keys) to cancel the operation.
Select + (press the Value key) to continue, or
select - (press the Shift and Value keys) to
cancel.
Press + to verify that the disk is to be formatted
or press - to skip formatting the disk. This
message will not display for new/unformatted
disk (e.g. The disk is to be formatted for the 1st
time)
Press the Enter/Cancel key to begin testing the
printer hard disk.
To stop the disk test, press the Enter/Cancel
key again. Once the test is stopped, you will be
asked to FORMAT DISK after printer restarts.
Press the Enter/Cancel key to end testing the
printer hard disk.
The printer will automatically restart to format
the hard disk.
Wait a moment for the operation to complete.
Press the Enter key to restart the printer.
Select + (press the Value key) to continue, or
select - (press the Shift and Value) to cancel.
Select + (press the Value key) to begin format-
ting the Flash ROM, or select - (press the Shift
and Value keys) to cancel the operation.
Wait a moment for the operation to complete.
Wait a moment for the operation to complete.
Select + (press the Value key) to clear the device
password, or select - (press the Shift and Value
keys) to cancel the operation.
Download Service Manual And Resetter Printer at http://printer1.blogspot.com
- FY8-13HQ-000 1
- Use of this manual should 2
- INTRODUCTION 3
- CONTENTS 4
- CHAPTER 1 PRODUCT OUTLINE 4
- CHAPTER 4 TROUBLESHOOTING 5
- CHAPTER 3 MECHANICAL SYSTEM 5
- PRODUCT OUTLINE 6
- I. FEATURES 7
- II. SPECIFICATIONS 8
- CHAPTER 1 10
- III. SAFETY 11
- IV. NAMES OF PARTS 12
- V. INSTALLATION 15
- VI. RELOCATING THE PRINTER 27
- VIII. USING THE PRINTER 31
- OUTLINE OF OPERATION 39
- I. BASIC OPERATION 40
- II. ENGINE CONTROL SYSTEM 46
- Developing DC 60
- Comparison 60
- High-voltage 62
- III. LASER/SCANNER SYSTEM 69
- 12.6 sec (approx.) 75
- IV. IMAGE FORMATION SYSTEM 76
- Photo conducting layer 77
- Substrate 77
- Surface potential (V) 79
- Photosensitive drum 79
- Primary charging roller 79
- Laser beam 80
- Dark area Light area 80
- Transfer charging roller 82
- Static eliminating brush 82
- V. PICKUP/FEEDING SYSTEM 85
- VI. VIDEO CONTROL SYSTEM 98
- CHAPTER 2 100
- VII. PAPER FEEDER 104
- CHAPTER 3 110
- MECHANICAL SYSTEM 110
- I. EXTERNALS AND CONTROLS 111
- III. DRIVE MECHANISMS 125
- IV. FEEDING MECHANISMS 127
- V. EXPOSURE MECHANISMS 135
- VI. CHARGING/DEVELOPING/ 136
- CLEANING MECHANISMS 136
- VII. FIXING SYSTEM 137
- [17][16] 140
- [10][11] 143
- VIII. PAPER FEEDER 144
- CHAPTER 4 151
- TROUBLESHOOTING 151
- I. INTRODUCTION 152
- Is the delivery 153
- Canon Inc., LBP-2000 Printer 158
- Configuration Page 158
- III. MEASURES AGAINST JAMS 168
- IV. FEEDING FAULTS 172
- V. MALFUNCTIONS 174
- [3][6][7] [4][5] 191
- APPENDIX 204
- I. GENERAL TIMING CHART 205
- II. GENERAL CIRCUIT DIAGRAM 207
- Paper feeder controller PCB 208
- III. LIST OF SIGNALS 209
- IV. MESSAGES TABLE 214
- CANON INC 222
Produits connexes et manuels pour Imprimer et scanner Canon LBP-2000
(76 pages)
(201 pages)
(327 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.848 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels