Canon TX-F Spécifications Page 35
- Page / 78
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5.2 FULL AUTO/AUTO Measurement
– 25 –
Press R/L switch to measure the other eye. Alignment will be started automatically.
Or, if the other eye already has been measured, press
PRINT switch to printout the
result.
NOTE: Value may become high when the eye is covered by eyelashes or eyelid.
♦ If warning image appears
If “WARNING IMG” is set to
“
ON” in SET mode, eye front
image taken at moment when the
error occurred will be displayed
on the monitor.
If the eyelid or eyelashes are
below the eyelid warning line,
take remedial action and then
press
START switch again to
perform measurement.
Move measurement head toward the other eye
FULL AUTO mode
After the required number of data is obtained, measurement head automatically
moves toward the other eye.
AUTO mode
Press R/L switch in order to move the measurement head toward the other eye.
Alignment and measurement of the other eye are performed
FULL AUTO mode
Alignment and measurement are
performed automatically in the
same ways as measuring the
right eye is done when the pupil
of the left eye has been detected.
AUTO mode
Display the other eye some-
where on the monitor and press
START switch.
Measure as many times as
required.
FULLAUTO(3)
No. 000001
mmHg
STD
[ , , ]
L
[ , , ]
30
R ERROR
Eyelid warning line
7
8
FULLAUTO(3) No. 000001
mmHg
STD
[ , , ]
[ , , ]
30
R
11 12 12 11.7
12 14 15 13.7
L
- Operation Manual 1
- PLEASE NOTE 2
- Safety Information 3
- General Safety Information 4
- See manual 8
- Mirar el manual 8
- Contents 9
- 1. Overview 11
- 3. Description 13
- 3.1.2 Examinee’s Side 14
- 3.3 Operation Panel 16
- CHIN REST 17
- 3.4.2 After Measurement 19
- No. 000001 20
- DISPLAY MODE 21
- 4. Measurement Modes 22
- 5. Measurement 25
- Check the settings 26
- Select the eye to be measured 26
- 5.1 Preparation 27
- IMPORTANT 28
- LIMITER switch 29
- LIMITER OFF” 29
- Select FULL AUTO or AUTO mode 30
- External eye fixation lamps 31
- Start measurement 32
- ♦ If level meter is low 34
- WARNING IOP” in SET 34
- The result is printed out 36
- 5.3 MANUAL Measurement 37
- Perform alignment 38
- Perform focusing 39
- Measure the eye 39
- Print/transfer the result 40
- How to enter SET mode 42
- How to change the page 42
- How to go out of SET mode 42
- PAG EEND PAGE 43
- END PAGE 46
- 7.3.1 About the Display 49
- 7.3.3 How to Insert 50
- 7.3.4 How to Delete 51
- 8.1 Inspection 53
- Problem Cause Remedy 55
- 8.3 Cleaning and Disinfection 61
- 8.3.3 Forehead Rest 62
- 8.3.5 Trackball 63
- Attach the cover 64
- 8.4 Replacement 65
- 8.4.2 Printing Paper 66
- Load the roll of paper 67
- Raise the printer lever 67
- Turn ON the power 67
- Close the cover 68
- 8.5 Expendable Parts List 69
- 9. Installation 70
- 9.1 Installation 71
- 10. Service Information 73
- 11. Specifications 74
- 12. Components 76
- Telephone: (81)-28-667-5711 78
- Telephone: (1)-949-753-4162 78
Produits connexes et manuels pour Mesure, test et contrôle Canon TX-F
(184 pages)Triplett Measuring instruments user manuals
Starting on F
Commentaires sur ces manuels