Canon iP8500 - PIXMA Color Inkjet Printer Manuel de service

PIXMA iP8500SERVICEMANUALCanonCopyright 2004, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A.

2-2. Service Call Errors (by LED Blinking in Orange and Green Alternately, or Lit in Orange) *1: Before replacement of the logic board ass'y, c

2-4. Troubleshooting by Symptom *1: Before replacement of the logic board ass'y, check the waste ink amount (by service test print or EEPROM in

3. REPAIR 3-1. Notes on Service Part Replacement (and Disassembling / Reassembling) *1: General notes: - Make sure that the flexible cables and wir

3-2. Special Notes on Repair Servicing (1) Flexible cable and harness wiring, connection Be careful of wiring of the flexible cables and harness. Im

3-3. Adjustment / Settings (1) Paper feed motor adjustment Perform the following adjustments when the paper feed motor unit is replaced: 1) When at

(3) Grease application 1 - 9

Note: 1 drop = 9 to 18 mg To the topPart name Where to apply grease / oil Grease / oil nameGrease / oil amountChassis 1 Entire sur

(4) Waste ink counter setting When the logic board ass'y is replaced, reset the waste ink counter. In addition, according to the waste ink amoun

<Service mode operation procedures> 1) With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power but

3-4. Verification Items (1) Service test print <Print check items> On the service test print (sample below), confirm the following items: - Ch

PIXUS iP8600 PIXMA iP8500 SERVICE MANUAL Revision 0 QY8-13A5-000 COPYRIGHT©2004 CANON INC. CANON PIXUS iP

<Service test print sample> (2) EEPROM information print <How to read EEPROM information print> Print sample: iPXXXX V1.00 IF(USB1=1 USB

IC(G=028 R=028 PM=028 BK=201 PC=028 C=182 M=169 Y=249) P_ON(S=00009 H=005 A=000) A_REG=1 M_REG=0 UR(A(Goe)=+01 B(Roe)=-01 C(PMoe)=+01 D(Bkoe)=-01 E(P

4. PRINTER TRANSPORTATION This section describes the procedures for transporting the printer for returning after repair, etc. 1) In the service mode

Part 2 TECHNICAL REFERENCE

1. NEW TECHNOLOGIES (1) Larger color space by 8 colors of ink (6 colors + red + green) By adding the red and green ink, a larger color space than th

2. CLEANING MODE AND AMOUNT OF INK PURGED To prevent printing problems due to bubbles, dust, or ink clogging, print head cleaning is performed before

3. PRINT MODE3-1. Resolutiondefault settingcan be selected on Main tabcustom settingInk: 8 color : BCI-6G/R/PM/PC/C/M/Y/BK7 color : BCI-6R/PM/PC/C/M

(2)Grayscale PrintingPrinter Driver's Custom setting Fast <-- --> FinePaper Type 54321Plain Paper Print quality Custom DraftStandard HighRe

(4)Duplex PrintingPrinter Driver's Custom setting Fast <-- --> FinePaper Type 54321Plain Paper Print quality Custom DraftStandard HighResol

4. FAQ (Problems Specific to the iP8500 and Corrective Actions) No. * Function Phenomenon Condition Cause Corrective actionPossible call or complaint

Scope This manual has been issued by Canon Inc., to provide the service technicians of this product with the information necessary for qualified pers

*1: Change the paper in each Bottom plate cleaning. The cleaning can end when paper does not get any soiling. *2: Locations to clean in servicing wh

PIXMA iP8500 Specifications <Printer> *1: Only for CD-R printing supported regions <Print head> To the topType Desktop serial color bub

I. MANUAL OUTLINE This manual consists of the following three parts to provide information necessary to service the PIXMA iP8500: Part 1: Maintenance

II. TABLE OF CONTENTS Part 1: MAINTENANCE 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consuma

Part 1 MAINTENANCE

1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer (1) Adjustment No

1-3. Product Life (1) Printer Specified print volume (I) or the years of use (II), whichever comes first. (I) Print volume (II) Years of use PIXM

2. LIST OF ERROR DISPLAY / INDICATION Errors are indicated by the LED, and warnings are displayed on the monitor of the computer connected to the pri