Canon 1200S Guide de démarrage rapide

read this firstCanon Color Image ScannerCanoScan FB1200SGetting StartedInspect the package contents▼Setting Up the scanner▼Installing the software▼T

8 FB1200S Getting StartedHow to Install the SCSI CardHave a Phillips (+) screwdriver handy and follow the procedures belowto install the AVA-2902E

FB1200S Getting Started 96Gently insert the SCSI card all the way into the PCIbus slot.• Insert the SCSI card in straight, being careful not to ti

10 FB1200S Getting StartedStart WindowsAfter you have installed the SCSI card, start the Windows program.1Turn on the computer.▼After a few moment

FB1200S Getting Started 11•If the scanner is already connected to the SCSI card, the NewHardware Found dialog (old Windows 95 version) or Device D

12 FB1200S Getting Started3Click the [Device Manager] tab and click the [+]mark beside the SCSI Controller item.• The SCSI card is operating corre

FB1200S Getting Started 13Installing the SCSI DriverAfter the SCSI card has been installed, you should install the SCSIdriver from the CanoScan Se

14 FB1200S Getting Started2Click [Install the SCSI driver].▼Installation of the SCSI driver will commence.3Follow the instructions in the window t

FB1200S Getting Started 15Confirming the Status of the SCSI Card with Windows NT 4.0After you have installed the SCSI card and driver, use theproc

16 FB1200S Getting StartedConnecting to the ComputerThis section explains the procedures for connecting the scanner to thecomputer. Until the scan

FB1200S Getting Started 173Attach the supplied SCSI interface cable to theSCSI connector on the computer.• The connectors on both ends of the SCSI

Describes operating procedure from set up and software installation to scanning and confirmation of operation. Please read before using the scanner fo

18 FB1200S Getting Started4 Connect the other end of the SCSI interface cableto the scanner’s SCSI connector.• This scanner is equipped with two d

FB1200S Getting Started 196Attach the power cord to the AC adapter.7Close the document cover. Plug the power cordinto an electrical outlet.• Ensur

20 FB1200S Getting StartedInstalling the SoftwareThis section explains how to install the software contained on the accompanyingCD-ROM.List of Sof

FB1200S Getting Started 21Macintosh• Plug-in Module CS-S Approx. 700 KB (English version)(Multiply this by the number of programs with which i

22 FB1200S Getting StartedInstalling the Scanner SoftwareWindowsIt is now time to install the software required to operate the scanner. This secti

FB1200S Getting Started 23C Click the [Browse] buttonand specify the CD-ROMdrive in the input box.Although this example uses[D:] as the CD-ROM dri

24 FB1200S Getting StartedAdd New Hardware Wizard Displays (Windows 98)A Click the [Next] button.B Select [Search for the bestdriver for your devi

FB1200S Getting Started 25F Click the [Finish] button.▼Windows will start.G Remove the CanoScan Setup Utility CD-ROM from the drive.4 Place the Ca

26 FB1200S Getting Started5Click the [Install/Uninstall Software] button.▼The following window will display.• If you accidentally click the wrong

FB1200S Getting Started 27•Please see the Users Registration Card for the serial numberrequired to install Adobe Photoshop 5.0 LE.• If the install

Thank you for purchasing the CanoScan FB1200S color image scanner.This Getting Started guide explains the necessary steps to connect the scanner toyou

28 FB1200S Getting StartedTrying Out the ScannerWindowsThe following instructions show you how to test the scanner and experiment withtwo software

FB1200S Getting Started 29Run the Scanning Software1 Place your document on the document glass asillustrated.• For the purposes of calibration, a

30 FB1200S Getting Started3 Choose [CanoScan FB1200S] from the list and clickthe [OK] button.4Click the [File] menu and select [Import] and[TWAIN_

FB1200S Getting Started 31MacintoshWindows• NOTE •• Calibration enables the scanner to reproduce colors moreclosely aligned to the original tones.

32 FB1200S Getting StartedMacintoshWindowsWARNINGPerform Scanning1To initiate the final scan, click the [Scan] button.• The final scan will be per

FB1200S Getting Started 33• NOTE •• The size of the image in the window will depend on thescanning resolution used. For ScanGear CS-S operating de

34 FB1200S Getting StartedInstalling the Scanner SoftwareMacintoshThe following procedures are for installing the software onto the Macintoshplatf

FB1200S Getting Started 35MacintoshWindows4Click the [Install Software] button.▼The following window will appear.• Begin by installing Adobe Photo

36 FB1200S Getting Started6 If the Adobe Photoshop 5.0 LE installation iscomplete and the following message displays,click [Restart].▼The computer

FB1200S Getting Started 378Click the [Install Software] button again.▼The following window will display.• Next, install the application programs o

Table of ContentsCHAPTER 1Setting Up the ScannerBefore using this scanner for the first time, follow theprocedures in this section to connect to the c

38 FB1200S Getting Started10 Click the [Start Installation] button at the bottomright of the window.• Do not restart the computer or remove the CD

FB1200S Getting Started 39• If the installation is unsuccessful even when all the prescribedprocedures are followed.Installation does not seem to

40 FB1200S Getting StartedTrying Out the ScannerMacintoshThe following instructions show you how to test the scanner and experiment withtwo softwa

FB1200S Getting Started 41MacintoshWindowsRun the Scanning Software.1 Place your document on the document glass asillustrated.• For the purposes o

42 FB1200S Getting StartedMacintoshWindows• NOTE •• Calibration enables the scanner to reproduce colors moreclosely aligned to the original tones.

FB1200S Getting Started 43MacintoshWindowsPerform Scanning1To initiate the final scan, click the [Scan] button.The Plug-in Module CS-S window will

44 FB1200S Getting StartedMacintoshWindows2Retouch or save the image as required.• Plug-in Module CS-S does not save the image, it only displays i

CHAPTER 2Guide to the SoftwareHere, we introduce each program that wasinstalled in the last chapter.How to Use the Software ...

46 FB1200S Getting StartedHow to Use the SoftwareThe following software is included with this scanner.Windows• ScanGear CS-S 4.3• ScanGear Toolbox

FB1200S Getting Started 47Using ScanGear CS-SScanGear CS-S is a program that loads images. You can also use it to adjust theimage as it is scanne

FB1200S Getting Started 3Features of the CanoScan FB1200SThis scanner is a flatbed color scanner with 1200 dpi optical resolutionincorporating the

48 FB1200S Getting StartedHow to Use ScanGear CS-S• Starting ScanGear CS-SSelect [TWAIN_32] as a TWAIN driver from a program (p. 29).• How to View

FB1200S Getting Started 49MacintoshWindowsScanning with ScanGear Toolbox CSScanGear Toolbox CS is a software which makes scanning easier. You can

50 FB1200S Getting StartedScanning withAdobe Photoshop 5.0 LEAdobe Photoshop 5.0 LE can retouch and manipulate images.Convenient Applications of A

FB1200S Getting Started 51Scanning withCaere OmniPage Limited EditionCaere OmniPage Limited Edition is an optical character recognition (OCR) prog

52 FB1200S Getting Started• How to View the Electronic ManualPlace the CD-ROM in the CD-ROM drive, click [View the ElectronicManuals] and click [C

FB1200S Getting Started 53Using Plug-in Module CS-SPlug-in Module CS-S is a software which acquires the image. The image file tosatisfy you can b

54 FB1200S Getting StartedHow to Use Plug-in Module CS-S• Starting Plag-In Module CS-SSelect [Canon PI CS-S 3.6] as a plug-in from the application

FB1200S Getting Started 55MacintoshWindowsScanning withCanoScan Toolbox CSCanoScan Toolbox CS is a software which makes scanning easier. You can

56 FB1200S Getting StartedScanning withAdobe Photoshop 5.0 LEAdobe Photoshop 5.0 LE can retouch and manipulate images.Convenient Applications of

FB1200S Getting Started 57Viewing Electronic Manualswith Adobe Acrobat Reader 3.0The operation procedures for Product Guide, ScanGear CS-S, Plug-i

CHAPTER 1Setting Up the ScannerIn this section, we explain the step-by-step procedures forsetting up the scanner from opening the package to checkingt

58 FB1200S Getting Started3 Select the manual you wish to view.• Adobe Acrobat Reader will automatically start and display themanual. Navigate thr

FB1200S Getting Started 59System InformationThis form is used to record the operating environment of the purchased scanner.If any problems occur w

60 FB1200S Getting StartedUse of shielded cable is necessary to comply with the technical requirements of the EMC Directive.Caution:1. No part of

I-IE-025BA ©CANON INC. 1999 PRINTED IN JAPANCANON (UK) LTD.Woodhatch, ReigateSurrey RH2 8BF, United KingdomFor technical support, please contact Canon

FB1200S Getting Started 5Inspecting the Package ContentsAfter opening the box, inspect its contents.Scanner Unit and AccessoriesSoftware and Docum

6 FB1200S Getting StartedSetting Up the ScannerUnlock the Scanning UnitThe scanner is shipped with the scanning unit locked to preventdamage durin

FB1200S Getting Started 7Installing the SCSI CardThese procedures are only required for use of the scanner with the Windowsplatform.What is a SCSI