Canon PIXMA MP600 Manuel de service

PIXMA MP600 /MP600RSERVICEMANUALCanonCopyright 2006, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon

- Faulty EEPROM data of the print head. [1405] - Print head hardware error. [1682] incorrect. Install the correct print head.Inner cover open. [1841]

button, the automatic print head alignment will not be re-done. The remaining ink amount unknown. [1683] U130 (Applicable ink tank icon) The remai

2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (COPY button), or Alarm LED Lit in Orange) Service call errors are indic

*1: Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information print). If th

2-3. Other Error Messages Part 1: MAINTENANCE TABLE OF CONTENTSMessage on the LCD Cause SolutionThe selected paper cannot be fed from cassette. Cha

2-4. Warnings Part 1: MAINTENANCE TABLE OF CONTENTSWarning Message on the LCD SolutionLow ink The following ink is low. Continue? (Icon of each i

2-5. Troubleshooting by Symptom Part 1: MAINTENANCE TABLE OF CONTENTS Symptom SolutionFaulty operation The power does not turn on. The power turns

- logic board*1. - Remove foreign material from the purge unit caps, if any. - Replace the purge unit. Printing is faint, or white lines appear on pr

*1: Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information print). If th

3. REPAIR 3-1. Notes on Service Part Replacement (and Disassembling / Reassembling) Part 1: MAINTENANCE TABLE OF CONTENTSService partNotes on repla

I. MANUAL OUTLINE This manual consists of the following three parts to provide information necessary to service the PIXMA MP600: Part 1: Maintenance

*1: General notes: - Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly. [See 3-2. Specia

3-2. Special Notes on Repair Servicing Part 1: MAINTENANCE TABLE OF CONTENTS(1) External cover and scanner unit removal(i) Front cover L removal Ins

(iv) Remove 2 screws from the front of the machine (1 each on the right and left sides).(v) Remove the side covers L and R.(vi) Scanner lock arm unit

(vii) Main case removal Remove screws from the right and left sides of the paper ejection side.Remove screws from the right and left sides of the she

(2) Operation panel and LCD viewer unit removal (i) Separate the scanner unit from the document cover unit.(ii) Remove screws from the bottom of the

(3) Document pressure sheet replacement Be cautious of the following when replacing the document pressure sheet:(i) Position one of the corners of th

(4) Printer unit separation from the bottom case unit(i) Unlocking the carriage unit To remove the screw beneath the carriage unit in the home posi

(5) Flexible cable and harness wiring, connectionBe cautious of wiring of the flexible cables and harness. Improper wiring or connection may cause b

3-3. Adjustment / Settings (1) Paper feed motor adjustment 1) When attaching the motor, fasten the screws so that the belt is properly stretched (i

1-24

II. TABLE OF CONTENTS Part 1: MAINTENANCE 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumabl

Other 1 drop = 9 to 18 mg (3) Ink absorber counter setting When the logic board ass'y is replaced, reset the ink absorber counter. In additi

<Standalone machine operation> Turn on the machine. On the operation panel, press the HOME button, select Settings, and Maintenance or Device se

(5) Service mode A: Service test print, EEPROM initialization, Ink absorber counter resetting Note: At the end of the service mode, press the ON/

<Service mode operation procedures> 1) With the machine power turned off, while pressing the Stop/Reset button, press and hold the ON/OFF butto

B: Destination settings Note: After setting the destination, confirm the model name and destination in service test print or EEPROM information prin

3) In the printout, select the Pattern No. in which streaks or lines are the least noticeable, press the Stop/Reset button the same number of tim

3-1) LF correction value Note: - Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power

<1-3-3, (5) Service mode_A~C> 1-32

D: Left margin correction Adjust the left margin for duplex printing or printing from the cassette. 1) Duplex printing from the ASF and cassette In

3) Setting of the left margin correction value ("+" means to increase the left margin) Press the Stop/Reset button the specified number of

Part 2: TECHNICAL REFERENCE 1. NEW TECHNOLOGIES 2. CLEANING MODE AND AMOUNT OF INK PURGED 3. PRINT MODE 4. FAQ (Problems Specific to the MP600 and Cor

1-35

1-36

E: Ink absorber counter setting Set the ink absorber counter value to a replaced new EEPROM after the logic board is replaced in servicing. 1) Befor

F: Button and LCD test Confirm the operation after replacement of the operation panel unit, board, or LCD unit. 1) In the button and LCD test mode,

4-4) When the Easy-Scroll Wheel is rotated counterclockwise 1 round (24 steps), press the OK button. The color of all segments turns red. 5) Open t

<Flicker adjustment mode flowchart> <1-3-3, (5) Service mode_D~F> 1-40

3-4. Verification Items (1) Service test print <EEPROM information contents> On the service test print (sample below), confirm the EEPROM info

<Service test sample> <1-3-4, (1) Service test print> 1-42

3-4. Verification Items (2) EEPROM information print <How to read EEPROM information print> Print sample: Part 1: MAINTENANCE TABLE OF CONTENT

Printed items: <Scanner>SC=00034 SCAN_ER(ER0=0000 ER1=0000) SC-dpi(75＝00000 150=00000 300=00029 600=00005 1200=00000 2400=00000 4800=00000) SG(

Part 1 MAINTENANCE PIXMA MP600 TABLE OF CONTENTS

<Direct> 38. Language 39. Memory card use count (CDI = Card Install) 40. Total Card Direct print pages (CDP = Card Print)41. Card Direct p

4. MACHINE TRANSPORTATION This section describes the procedures for transporting the machine for returning after repair, etc. 1) In the service mode

Part 2 TECHNICAL REFERENCE PIXMA MP600 TABLE OF CONTENTS

1. NEW TECHNOLOGIES 1) Easy-Scroll Wheel With the Easy-Scroll Wheel, a menu can be easily selected by rotating the wheel clockwise or counterclockwi

The remaining ink amount will be checked at any of the following timings: - At the end of paper ejection*1 - At the end of print head cleaning - At

2. CLEANING MODE AND AMOUNT OF INK PURGED To prevent printing problems due to bubbles, dust, or ink clogging, print head cleaning is performed before

*1: The counter for the on-arrival cleaning is checked at opening and closing of the scanning unit (the first opening and closing only), before start

3. PRINT MODE 3-1. Normal Color Printing via Computer Part 2: TECHNICAL REFERENCE TABLE OF CONTENTS Default setting Selectable in the MP driver Mai

3-2. Normal Grayscale Printing via Computer 3-3. Borderless Printing via Computer Print control Ink used5 passes, Bi C/M/Y/c/m/k7 passes, Bi C/M/Y

3-4. Duplex Printing via Computer 3-5. Camera Direct Printing Paper type (Canon specialty paper)Item5 Fast4 3 2 1 FinePlain paper Print quality

1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer (1) Adjustment Par

3-6. Copying Paper type (Canon specialty paper)Item5 Fast4 3 2 1 FineCopy modePlain paper Single sided, B&W (borderless not supported)Print

4. FAQ (Problems Specific to the MP600 and Corrective Actions) Part 2: TECHNICAL REFERENCE TABLE OF CONTENTSNo. * Function Phenomenon Condition Cau

4 B Print resultsin automatic duplex printing (lines or streaks perpendicular to the paper feed direction)printing (Photo Paper Plus Double Sided, pos

*1: Change the paper in each Bottom plate cleaning. The cleaning can end when paper does not get any soiling. *2: Locations to clean in servicing w

2) Fold the paper at approx. 60 mm from the end, and fold the folded end in half backward, as shown below. 3) Moisten the folded end portion (i

Part 3 APPENDIX PIXMA MP600 TABLE OF CONTENTS

3. PIXMA MP600 SPECIFICATIONS <Machine> Part 3: APPENDIX TABLE OF CONTENTSType Desktop serial color inkjet printer Paper feeding method Auto

<Scanner> <Copy> Environmental requirements Humidity 10%RH to 90%RH (no condensation)Non operation Temperature 0C to 40C (32F to 104F

<Direct printing> - Notations for the Americas should be confirmed with the related marketing section of each sales company in the Americas.

Card Direct printing Print layout 1 photo per page (bordered/borderless, only with borders for plain paper) Index printing: A4/Letter: 80 photos per

Caution: DO NOT loosen the red screws at both ends of the carriage shaft, securing the print head position, as they are not re-adjustable. The red scr

<Print head> <Ink tanks> O: Usable X: Not usable Note: The ink tanks for the Japanese model are not compatible with those for the oth

4. PRINT MEDIA SPECIFICATIONS <Plain paper / Specialty paper> The following types of paper are recommended: *1: ASF only for LGL *2: When A4

1-3. Product Life (1) Machine Specified print volume (I) or the years of use (II), whichever comes first. (I) Print volume: 24,000 pages (II) Years

2. LIST OF ERROR DISPLAY / INDICATION Errors and warnings are displayed by the following ways: 1) Operator call errors are indicated by the Alarm LED