Canon CHDK Manuel d'utilisateur télécharger pdf (Page 16)

! Enable Fast EV Switch? Enable [•] / Disable [ ]

Warning: This feature is not properly workable on all cameras yet.

See: http://chdk.setepontos.com/index.php/topic,2595.msg24211.html#msg24211

and: http://chdk.setepontos.com/index.php/topic,2501.msg23321.html#msg23321

Turns your UP and DOWN buttons into quick EV compensation buttons. You no longer have to

press your FUNC./SET or MENU buttons to adjust your EV settings while shooting. By pressing

! ! ! ! ! ! ! ! ! ! ❶

UP or DOWN buttons the EV increased or decreased. There is also a screen display

showing your chosen EV-compensation settings by whatever step-size you have chosen (see

! ! ! ! ! ! ! ! ! ! ❷

Step Size (1EV)?) below). It is advisable to move your OSD EV override display over your

camera's own to prevent confusion.

You will see a real-time change in your EVF/LCD as you change your EV values with this short-

cut. It also works while the Zebra Mode is engaged. You can ﬁne-tune the Zebra alert just by

pressing the UP and DOWN buttons with half shoot.

When used in conjunction with the Curves "Auto DR" Mode you should never miss another

blown highlight or dropped shadow again.

One drawback: If using your up and down buttons during a half-press to see your Zebra

alerts while changing your EV setting, it will toggle your "Disable Overrides" on and off if you

have that feature engaged as well. A small price to pay for the ability to have these amazing

features. One work-around, set your EV step-size to 1/2 what you normally would use, then the

"Disable Overrides" shortcut will always toggle back to your original ON (or OFF) on every 2nd

EV +/- press, effectively resetting it where you wanted it in the ﬁrst place.

Note also: This change is not saved between camera power-downs. If you would always like to

start out with a small negative preset EV value to avoid blown highlights, then use Canon's own

EV compensation setting for your startup EV value. This Fast EV Switch will reﬂect that value

on startup.

❶: Enabled when Fast EV Switch is enabled.

❷: Use OSD parameters > OSD layout editor to move display.

•

Step Size (1EV)? [1/6 Ev, 1/3 Ev, 1/2 Ev, 2/3 Ev, 5/6 Ev, 1Ev, and on - ]

When using the Fast EV shortcut feature you can adjust how much you want to change your EV

compensation with each UP or DOWN keypress. Step size is increments. A major improvement

over the adjustment levels and steps in the original ﬁrmware.

Force manual ﬂash Enable [•] / Disable [ ]

For optional control over camera ﬂash output, use with Power of ﬂash [ 0, 1, 2 ] to give 3

separate steps up in ﬂash output power.

•

Power of ﬂash [ 0, 1, 2 ]

Used with Force manual ﬂash to adjust ﬂash output.

0 = Low, 1 = Medium, 2 = Very High

! ! More at:- Flash notes, and Force ﬂash pics. on page 58

Quality override! [ Superﬁne, Fine, Normal, off ]

For recent camera versions without Canon Superﬁne setting (SX200, SX20, etc)

Canon setting is used when “off” is selected, settings are saved in CCHDK.CFG

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Canon CHDK Manuel d'utilisateur Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à eau Canon CHDK