Canon VC-C50i Manuel d'utilisateur

NETWORK CAMERAUser’s ManualVB-C50i VB-C50iR´ENGLISHPlease read this User’s Manual carefully before operation.Be sure to read the “a Safe Use of Equipm

xa Safe Use of EquipmentaAn exclamation point, within a triangle, is intended to alert the user to the presence ofimportant operating and maintenance

4-30Setting Up a Normal ScheduleTo Make Settings...1. With the Normal Schedule displayed, selectan optional schedule number.The schedule track for the

4-31VB Administration ToolsContinued on the following page. aSchedule Setting ToolTip● On Weekly setting, if you specify the same time and the same da

4-32Tip● You can register different settings for each setting number. The number of settingnumbers that can be registered differs depending upon the s

4-33VB Administration ToolsSpecial ScheduleWith Special Schedule, you can set up a schedule on one specific day of the week. For example,on a public h

4-34Tip● You can only set one type of Special Day per day.● You can set one Special Day a maximum of 32 times.● You can also set up a Schedule by righ

4-35VB Administration Tools3. Double-click the sub-schedule track.The Special Schedule Settings dialog box appears.Enter settings for the schedule.4.

4-36Tip● An icon for the service you have set up appears in the schedule track in the calendar.However, where the schedule track is short, it may be t

4-37VB Administration ToolsTip●If you have set up a Normal Schedule (→ P.4-29) and a Special Schedule with the samestart and end time, the Special Sch

4-38Setting Up ServiceSet up the services to be performed in the schedules.To open the settings screen for each service, in the“Service” tab in the Sc

4-39VB Administration ToolsTimer Setting ToolThe section below describes the “Picture Recording” function that takes still images at specifiedtimes an

xiFCC NOTICENetwork Camera, Model: VB-C50FiN, VB-C50FiPThis device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two co

4-40Setting Up Picture RecordingTo Make Settings...1. With the Schedule Setting Tool, open the Timer Setting Tool.In the Service tab of the Schedule S

4-41VB Administration ToolsMotion Detection Setting ToolThe section below describes the motion detection function which records pictures, sends data t

4-42t Camera Selection boxFor selecting a camera.y ViewerFor picture display and camera control in the same way as a normal viewer.u Motion detection

4-43VB Administration ToolsFlow of Motion Detection SettingsA summary of the procedures for motion detection is given below. Please refer to each refe

4-44Setting Up Motion DetectionTo Make Settings...1. Open the Motion Detection Setting Tool with the Schedule Setting Tool.In the Service tab in a Nor

4-45VB Administration Toolsq Used AreaCheck the number of the motion detection area to be usedand the detection area frame is displayed in the Viewer.

4-46Tip● If Sensitivity is set at a low level, the device does not recognize the motion evenduring great variations in the image inside the motion det

4-47VB Administration ToolsqwerTip● See “Relationship between ON and OFF events and picture recording” (→ P.4-58)for the ON and OFF event and picture

4-486. Enter the settings for output to an externaldevice when the device detects motion(Output tab).* The settings in these steps are optional.Set ou

4-49VB Administration ToolsNote● Because the video distribution frame rate may be slowed when the data is sent viaa proxy server, connection without u

xiia IMPORTANT SAFETY INSTRUCTIONSIn these safety instructions, the word“equipment” refers to the Canon NetworkCamera VB-C50i/VB-C50iR and all itsacce

4-50TipMotion detection status and screen displayThe area in which the VB-C50i/VB-C50iR isperforming motion detection appears in a blueframe in the Vi

4-51VB Administration ToolsqwTipSetting the motion detection level while checking recordedimagesTo set the level of motion detection at motion detecti

4-52q w ertyuNight Mode Setting ToolBelow is a description of the Night Mode function with which you can take pictures in dark conditions.Night Mode S

4-53VB Administration ToolsSetting Up Night ModeTo Make Settings...1. With the Schedule Setting Tool, open the Night Mode Setting Tool.In the Service

4-54qw ertyui!1o!0!2External Device Input Setting ToolBelow is a description of the External Device Input function which performs video recording when

4-55VB Administration Tools!0 Post-event (sec.) and IntervalEnter the required number of seconds, within a range of 0-10 seconds for picture recording

4-56External Device Output Setting ToolThe section below describes the output settings to an external device connected to the Multi-Terminal Module (→

4-57VB Administration ToolsSetting Up External Device OutputTo Make Settings...1. With the Schedule Setting Tool, open the External Device Output Sett

4-58Schedule Setting ToolTipRelationship between ON and OFF events and picture recordingONOFF ONOFFONOFFPicture RecordingAB CDON OFFBelow are methods

4-59VB Administration ToolsTipE-mail Notification Settings dialog boxWhen pictures have been recorded, you can send the recorded picture and data inan

xiiifig-1EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODEANTENNA LEAD IN WIREANTENNA DISCHARGE UNIT (NEC SECTION 810-20)GROUNDING CONDUCTO

4-60Schedule Setting ToolTipAudio Playback Setting dialog boxTo play back audio, you have to register the audio file you want to play back. Settings f

4-61VB Administration ToolsThe Log Viewer is a tool for downloading log files, and viewing and managing the operating statusof the device. The Log Vie

4-62Log ViewerViewing the LogThe following content is displayed in the log.● CodeThe log displays error codes. For error codes, refer to Log Messages

4-63VB Administration ToolsUsing Selection Criteria to Display LogsLogs can be filtered according to error type, code, or date and time so that only t

4-64Admin ViewerAdmin Viewer is a viewer which has functions for managing the VB-C50i/VB-C50iR. It has specialprivilege functions that the Viewer for

4-65VB Administration ToolsStarting Up Admin ViewerTo Start Up...1. Click the “Admin Viewer” on the VBAdmin Startup Panel or double-click the“Admin Vi

4-66NoteDepending on the settings content, some operations are not available from Admin Viewer.Displaying and Saving the External Device Input and Mot

4-67VB Administration ToolsEnabling/Disabling View RestrictionsView restrictions can be enabled or disabled when controlling the camera.1. Choose eith

4-68Clicking the Screen to Control the CameraYou can control the pan, tilt and zoom operations by clicking and holding the mouse in the viewerto start

4-69VB Administration ToolsCamera-Specific FunctionsYou can set up camera-specific features such as settings for exposure, digital zoom and night mode

xiv - Locations exposed to direct sunlight - Locations exposed to salt spray - Close to flammable solvents (alcohol,thinners, etc.)22. When any of the

4-70Sending audioYou can send audio with the VB-C50i/VB-C50iR through the speakers installed on the optionalMulti-Terminal Module on the camera. Below

4-71VB Administration ToolsTip● The “Microphone setting” button will not appear in the following cases.• If Audio Reception has not been set up in the

4-72

Creating Web Pages forVideo DistributionThis chapter describes how to use the VB-C50i/VB-C50iR towebcast information.Picture data can be distributed i

5-2HTTP (WWW) serverDedicatedWeb serverViewer PC1 Access to Web pages3 Request for video4 Video distribution2 IP address information notificationInter

Creating Web Pages5-3Web Pages for Video DistributionTipYou can use the Language setting function for the Browser to create a multi-lingualWeb site. F

5-4There are 2 types of viewers: the Viewer for Java and the Viewer for PC.For a detailed explanation of the Viewers, please refer to “Viewer Software

Creating Web Pages5-5Viewer OverviewNote● Viewer Software User’s Manual is provided on the CD-ROM supplied with theVB-C50i/VB-C50iR (Viewer-E.pdf).● U

5-6This is a LiveApplet sample page which distributeslive videos and allows users to control the camera.This is a sample page which combinesLiveApplet

Creating Web Pages5-7This section describes how to use the Viewers for Java to provide videos. Application examplesare also given.Using the Viewer for

xvMaintenanceCleaning the Equipment1. Unplug the AC adapter from the wall outlet.2. Carefully wipe the equipment with a soft cloth that hasbeen moiste

5-8Using the Viewer for Java to Distribute VideosSaving Web Page DataThe VB-C50i/VB-C50iR is equipped with a Flash memory where Web page data can be s

Creating Web Pages5-9Using the Viewer for Java to Distribute VideosExample of Using the Viewer for Java to Create a Web PageThis section describes an

5-101 sample.htm<html><head><title>SampleSite LiveApplet</title></head><frameset rows="70,*"><frame s

Creating Web Pages5-11Click the button todisplay the page inwhich LiveApplet isembedded.Using Glimpse and LiveApplet TogetherThis section describes ho

5-121 glimps.htm<html><head><script language="JavaScript"><!--function clicked(btn) {url = btn.namewindow.open(url,&quo

Creating Web Pages5-13Providing “LiveApplet” without Camera ControlThis section describes how to create a Web page that only displays live video and h

5-14Certain Images SpecifiedStartup screen Disconnection screenIf no particular image is specified, the “connecting to hostname” (when the hostname pa

Creating Web Pages5-15Displaying the Host Name, Frame Count and Other Information on the Video Screen<param name=show_fps value="on">

5-16Displaying Bitmap Images on the Video Screen<param name=superimpose value="/local/logos/newlogo.gif,0,0">* The underlined portion

Creating Web Pages5-17Viewer for Java ParametersYou can specify applet parameters to provide an applet tailored to modify the behavior orappearance of

xvi

5-18Using the Viewer for Java to Distribute VideosWhen a startup screen is specified in the “open_image” parameter, this parameter specifies the displ

Creating Web Pages5-19Using the Viewer for Java to Distribute VideosSpecifies whether or not connection to the camera server should be established sim

5-20Using the Viewer for Java to Distribute VideosTipWhen specifying an address included in the codebase attribute of the applet tag anda URL paramete

Creating Web Pages5-21This section describes how to use the Viewer for PC to provide videos. Application examples arealso given.If a client is using t

5-22TipInstead of an IP address, you can also type in <_I_P_A_D_D_R_> (→ P.5-9).Example: <_I_P_A_D_D_R_> 65310<_I_P_A_D_D_R_> 65311w

Creating Web Pages5-23Using the Viewer for PC to Distribute VideosInclude the tags that link to the wvh file in the text or images in the Web page.1 &

5-24Distributing Videos Using a Browser OnlyYou can also use the WebView-HTTP protocol to provide videos from the VB-C50i/VB-C50iR directlyto a Web br

Creating Web Pages5-25GetStillImage ParametersParameter Descriptionp or panSpecifies the camera pan angle. “p” is a 1° unit, and “pan” is a 0.01° unit

5-26NoteContact respective manufacturers for details on setting the router.One fixed global address is required if the VB-C50i/VB-C50iR is being used

Creating Web Pages5-27You can view still images and control the camera using the Web service of a mobile phone. Youcan easily create still image distr

Before Using theVB-C50i/VB-C50iRThis chapter describes the features of the VB-C50i/VB-C50iR, the hardware and software requirements, and thename and f

5-28Example of Creating a Screen for Distribution of a Still Image to a Mobile PhoneCamera Control by Position SpecificationIf you use the sample page

Creating Web Pages5-29Example of Creating a Screen for Distribution of a Still Image to a Mobile Phonestill.jpg parametersCommand Descriptioncamera_id

5-30

Using the PictureRecording FunctionThis chapter describes a couple of specific examples of thePicture Recording function using the VB-C50i/VB-C50iR. S

6-2Using the Still Picture Recording Function Linked to an External DeviceBy combining various sensors and switches to operate according to External D

6-3Using the Picture Recording FunctionUsing the Still Picture Recording Function Linked to an External DeviceSample Still Picture Recording SettingsS

6-4Using the Still Picture Recording Function with a Predetermined ScheduleBy using the “Schedule” setting, you can construct a monitoring system that

6-5Using the Picture Recording FunctionUsing the Still Picture Recording Function with a Predetermined ScheduleSample Still Picture Recording Settings

6-6Using the Motion Detection Function with a Predetermined ScheduleBy running the motion detection function according to a schedule, you can construc

6-7Using the Picture Recording FunctionSample Still Picture Recording SettingsSettings specified on the “Camera and Video” page (→ P.3-7)Specify the a

1-2The VB-C50i/VB-C50iR is a system that distributes live videos via the Internet or an Intranet. Itcan be used in a wide range of applications, such

6-8● Next, set the sensitivity, area ratio and duration.To ensure that the event is not triggered by unrelatedlighting changes or small movements, set

6-9Using the Picture Recording FunctionUsing VBCollectorDownloaded image displaysPictures recordedwith the VB-C50i/VB-C50iR’s picturerecording functio

6-10Starting Up VBCollectorVBCollector is started up by choosing it from Start menu.To Start Up VBCollector...Choose [Program]-[WebView Livescope]-[VB

6-11Using the Picture Recording Function2. Enter each item in the various fields and clickthe “OK” button.q Server NameAssign a name for recognizing t

6-12TipDownloading images to a shared folder on the network● You cannot specify a path name that uses a network drive in the “Image Directory”setting.

6-13Using the Picture Recording FunctionNoteDownloaded images are not deleted when a server is deleted. To delete downloadedimages, first follow the p

6-14Registering TasksAdding a TaskAdd a new task for downloading images.To Add a New Task...1. To add a task, choose “New Task” from the“Task” menu ba

6-15Using the Picture Recording FunctionNote● Up to 16 tasks can be executed by VBCollector simultaneously. Please be surenot to load a schedule with

6-16Editing TasksThe details of a registered task can be edited.To Edit a Task...1. In the Task View, select the task to be editedby clicking on its n

6-17Using the Picture Recording FunctionDisplay Task StatusDuring the execution of any task, the download status can be checked.To View Task Status...

1-3Before Using the VB-C50i/VB-C50iRFeatures of the VB-C50i/VB-C50iRcontrast of the darker areas to make it easier to see. Unlike backlight compensati

6-18Starting/Stopping the ServiceThe task scheduler service can be started and stopped.To Make Settings...Choose “Start Service” or “Stop Service” fro

6-19Using the Picture Recording FunctionAutomatic Downloading by NotificationYou will not be able to record images if there is insufficient space on t

6-20r “Apply” buttonSaves a change to the reception port number in the registry. If you make a change, a dialogbox is displayed. Click “Yes” and the t

6-21Using the Picture Recording Function3. The Filter dialog box appears. Select thedisplay format and time and click the “OK”button.q Display FormatS

6-224. HTML for displaying the images is generated,the Web browser starts up, and thumbnailimages of the selected date are displayed in100-image units

6-23Using the Picture Recording FunctionAnimate ImagesDownloaded images can be selected using the server name and date to be animated (consecutivedisp

6-24● AnimationImages can be consecutively displayed.[Top] button Shows the original image.[Prev] button Shows the previous image.[Play/Pause] button

6-25Using the Picture Recording FunctionDeleting ImagesDownloaded images can be deleted.To Delete Images...1. Stop the task schedule of the tool.2. Ch

6-26Viewing LogsVBCollector outputs logs concerning the execution of tasks. To view a log, choose “Display Log”from the “Tools” menu bar.The following

6-27Using the Picture Recording FunctionDisplaying Logs According to Selection CriteriaLogs can be filtered according to error type, code, or date and

iiIntroductionThank you for purchasing the Canon Network Camera VB-C50i/VB-C50iR (referred to hereafteras the VB-C50i/VB-C50iR).This User’s Manual des

1-4VB Administration Tools Ver. 2.1 (→ P.4-2)This tool lets you create panorama pictures from the VB-C50i/VB-C50iR and then easily use themto visually

6-28Search LogsLogs can be searched using character strings. This function is convenient in case of searchingany target log from among numbers of logs

6-29Using the Picture Recording FunctionSelecting Log FilesThe initial log file of VBCollector is saved as “vbrpd.log” file in the “SYSTEM” folder wit

6-30Setting Download CapacityIn order to perform downloads based on a task schedule, you can set the upper limit on thenumber of pictures or specify t

AppendixChapter

7-2TroubleshootingBefore you contact your Canon dealer or service outlet, check the items listed below. If a logmessage is displayed, refer to the log

7-3AppendixTroubleshootingI forgot the password.● All factory defaults settings can be restored by using the Reset switch (→ P.7-24). Thedefault admi

7-4MessageExplanationResponse●A007 View restriction setting error (warning)inconsistent view restriction for camera[1]The view restriction settings ar

7-5AppendixLog MessagesMessageExplanationResponse●A008 Compatibility error in the view restrictions settings (warning)unacceptable view restriction fo

7-6MessageExplanation●A023 Detection in change of point of contact (err)a %1 detected at In%2%1point of contact device input change (front-edge | rear

7-7AppendixLog MessagesMessage●A050 Access permission when restricting user access (info)user %1 access grantedExplanationDuring user access restricti

1-5Before Using the VB-C50i/VB-C50iRVBCollector Ver. 2.1 (→ P.6-9)This tool is for collecting and viewing still pictures recorded by the VB-C50i/VB-C5

7-8Message●B102 Client connection denied (notice)%1 request denied[%2]%1Client host IP address%2Denial type (41 | 42 | ...)ExplanationResponseClient c

7-9AppendixLog MessagesMessage●B103 Client access forced disconnection (notice)%1 access denied[%2]Explanation%1Client host IP address%2Denial type (4

7-10Log MessagesMessage●B403 Settings change failure (crit)cannot set config[%1]%1Error numberResponseIf rebooting does not solve this problem, there

7-11AppendixMessageExplanation●S005 System settings changed (info)System settings updatedThe VB software settings were modified without a reboot. Sy

7-12Log MessagesFault SeverityFault which affects task executionFault which does not affect task executionLevelErrorWarningInformation on correct oper

7-13AppendixLog Messages●S007 (err)Message Execution failure: Invalid server information●S008 (err)Message Download is completed, but failed to get ta

7-14●S016 (info)Message Logs generated at the previous task will be merged.Explanation If logs generated while task operation are not output to the ma

7-15AppendixLog Messages●D012 (err)Message Failed to get the server information.●D013 (err)Message Cannot create a new directory.●D018 (err)Message Wo

7-16Log Messages●D029 (err)Message Download was aborted due to insufficient disk space.[%1 remaining, %2required]%1 Disk space currently available [MB

7-17AppendixLog Messages●D038 (warning)Message Downloading of old images is not available. [Images captured before %1]%1 The oldest captured date of a

1-6If you finish setting the VB Initial Setup Tool (initial settings) or wish to stop the AutomaticDownload by Notification function using VBCollector

7-18VB-C50i/VB-C50iRVideo signal Conforms to NTSC/PALImage Sensor 1/4-inch CCDNumber of pixels [NTSC] use: 340,000 (effective 630,000)[PAL] use: 400,0

7-19AppendixSpecifications+3.3V0.1µF10kΩ 10kΩ10kΩInternal controllerInput terminals IN+, IN–Output terminals OUT A, OUT B+–External Device I/O Termina

7-20Note● Install the Viewer for PC from the “VBToolsInstall.exe” file on the supplied CD-ROM (→ P.2-11).● The User’s Manual for the viewer software i

7-21AppendixSample Network ConfigurationsThis section describes some typical installation modes for the VB-C50i/VB-C50iR.Be sure to assign an IP addre

7-22Upgrading the Firmware RemotelyNoteDo not turn the power off until you have confirmed that the VB-C50i/VB-C50iR hasrestarted. Turning the power of

7-23AppendixRestoring the Factory Default SettingsSince the VB-C50i/VB-C50iR supports a wide variety of functions, we recommend that you makea note of

7-24Restoring the Factory Default SettingsNote● Do not turn the VB-C50i/VB-C50iR power off while the Restoring operation. If youturn the power off, al

7-25AppendixFactory Default SettingsItem Setting Item Setting 1 Item setting 2 (m) (d) (y) (m) (d) (y)● Administrator ID root● Adm

7-26Factory Default SettingsItem Setting Item Setting 1 Item setting 2 (m) (d) (y) (m) (d) (y)● Server(Common Settings)Maximum Num

7-27AppendixIndexAAC adapter ... iv, 2-6AC cable ...

1-7Before Using the VB-C50i/VB-C50iRViewer Software for Monitoring Use (Sold separately)If WebView Livescope MV Ver. 2.1 is used, up to 16 viewer scre

7-28IndexHost Name ... 4-5Host Specification ...

7-29AppendixIndexAnimate ... 6-23Deleting ...

7-30

CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanU.S.A. CANON U.S.A.,INC. NEW JERSEY OFFICE100 Jamesburg Road, Jamesburg, NJ 08831

1-8System Components and Their OperationVB-C50iCamera headBasePower connection socketMulti-connectorYou can connect the Multi-TerminalModule(VB-EX50)

1-9Before Using the VB-C50i/VB-C50iRSystem Components and Their OperationVB-C50iRMounting plateBaseLAN status LEDThe LED blinks during communication.1

1-10VB-C50iVB-C50iRSystem Components and Their OperationBottomOn the bottom of the VB-C50i/VB-C50iR there are the MAC address required for network set

1-11Before Using the VB-C50i/VB-C50iRUsing the Multi-Terminal Module (VB-EX50), you can connect external devices such as differentkinds of sensors and

1-12

Setting UpThis chapter explains how to set up the VB-C50i/VB-C50iR,run initial checks, and confirm that the camera’s images aredisplayed correctly.Cha

iiiRequest concerning disclosure of live videosWith respect to the disclosure of live videos, we request that sufficient consideration begiven to matt

2-2Set up the camera1Perform initial settings for the camera3Connect the camera to the network2LAN cableVB-C50iHubSet up the device.Make sure the devi

2-3Setting UpSetup WorkflowInstall the software5Check operation of the camera4Access the device with your PC, then display to check the image from the

2-41. Set Up the Cameraa WARNING:Install the camera securely.● When installing the VB-C50iR on the ceiling, contact your Canon dealer.● When installin

2-5Setting Up1. Set Up the Cameraa WARNING:The Wide Converter WL-37 is designed specifically for the VB-C50i and cannot beused on the VB-C50iR.Note● T

2-6Turning the Power ON and OFFThe VB-C50i/VB-C50iR itself does not have a power switch. You can switch the VB-C50i/VB-C50iR on by plugging the AC ada

2-7Setting UpOnce your PC and the camera are connected, perform the initial settings next. The instructionshere follow on from “2. Connect the Camera

2-83. The camera connected to the networkis automatically detected and its MACaddress, IP address and model nameare displayed.The factory default sett

2-9Setting Up5. A setup progress window appears andyour settings will be saved.Note● Set the IP address to a value that suits your environment.● Where

2-102. Your Web browser starts up and thetop page of the camera server appears.Click the “Using Viewer for Java” or the“Using Viewer for PC” and check

2-11Setting Up5. Install the SoftwareYou must install software to display images from the camera and to manage the camera. Thereare 3 types of softwar

ivPackage ContentsThe VB-C50i/VB-C50iR package contains the following items. If any of these items is missing,please contact the retailer from which y

2-12Viewer Software OverviewBy using the Viewer software, you can view images sent from the VB-C50i/VB-C50iR on a PC, aswell as control the camera. Be

Basic SettingsThis chapter describes the basic settings for the VB-C50i/VB-C50iR such as network connection, camera control, dateand time setting and

3-2What Can I Do on Each of the Settings Pages?Proceed to each of the settings pages from the Settings Title Page where you can perform varioussetting

3-3Basic SettingsAccessing the Settings Title PageNoteThis manual uses the IP address 192.168.100.1 (the factory default setting) below asan example t

3-4Settings Title PageFrom the Settings Title Page, you can move to each settings page, confirm the settings afterchanging, and save the changes to th

3-5Basic SettingsYou can perform the following settings with System and Network.● Root Account: For setting up passwords.● Ethernet: For setting up IP

3-6Ethernet 1 “Address Setting Method”Select an address setting method from “Auto Setting (DHCP)” or “Manual Setting”. If you select“Auto Setting (D

3-7Basic SettingsYou can perform the following settings with Camera and Video.● Video Capture: For setting image size and quality.● Camera Control: Fo

3-8Camera Control1 “Shutter Speed”Sets the camera shutter speed.2 “Focus Mode”Sets the focusing mode for the camera.Select the focusing mode for the c

3-9Basic SettingsTipThe operating range of the camera heads on the VB-C50i/VB-C50iR is shown below.NoteDo not attempt to manually change the camera he

vContentsIntroduction ... iiPackage Contents ...

3-10Tip● Controllable range and shootable range are shown below.0°+-+-Extent of pan controlMaximum horizontal extent of the video capture rangeExtent

3-11Basic SettingsCamera Names1 “Camera Name”Used in the camera selection box on the viewers (→ P.1-4). This setting is required.1Setting Camera Contr

3-12Presetting Best Shot (Preset)You can perform the following settings with Preset.● Common Settings: For setting the tour schedule of present positi

3-13Basic Settings1 “Restrict Camera Control to Presets”Camera control by using the Viewer for PC and the Viewer for Java can be restricted to thepres

3-14Preset 1-20NoteChanges in the preset settings are not applied to the viewer while it is connected.Presetting Best Shot (Preset)1321 “Application”U

3-15Basic SettingsTipYou can make preset settings more easily with the VB Administration Tools. Pleaseuse the VB Administration Tools for the settings

3-16You can perform the following Settings with Server.● Common Settings: For setting up the environment where users can connect to theVB-C50i/VB-C50i

3-17Basic SettingsHTTP Server1 “HTTP Port”Sets the TCP port number for the HTTP. Enter a value between 1 and 65535. The defaultsetting is 80.2 “Global

3-18Camera Server1 “Video Transmission Port”Sets the TCP port number for the video transmission protocol. Enter a value between 1 and65535. The defaul

3-19Basic SettingsAudio Server1 “Audio Reception”Set “Audio Reception” to “ON” to receive audio which has been sent from the Admin Viewerand output to

viContentsSetting Camera Control, Image Size and Quality (Camera and Video) ... 3-7Presetting Best Shot (Preset) ...

3-20Setting User Access Privileges (Access Control)You can perform the following settings with Access Control.●Authorized User Account: Register users

3-21Basic SettingsAuthorized/Restricted Host SpecificationNote● If you do not make a Host List, access is permitted to any host.● If the Host List pro

3-22TipThe Host Restriction function applies to hosts running client applications such asviewer. Access restrictions are imposed using a list made up

3-23Basic SettingsSetting the Date and Time (Date and Time)You can perform the following settings with Date and Time.● Current Camera Time: Displays t

3-24New Camera Time1 “Synchronize with computer time”Sets to the date and time of the PC currently accessing the VB-C50i/VB-C50iR via a Webbrowser.2 “

3-25Basic SettingsYou can perform the following settings with Miscellaneous.● DNS: Register the Name Server Address and Host Name for registering host

3-26Mail1 “Mail Server Host”Specifies the SMTP server.2 “Sender’s (From) Mail Address”Specifies the mail sender.3 “Recipient (To) Mail Address”Specifi

3-27Basic SettingsExternal Device Names1 “External Input Device 1-2”“Device Name”To distinguish between the different external devices connected to th

3-28You can perform the following settings with the Administration Tools.● On-board File System Information: Displays the status of VB-C50i/VB-C50iR’s

3-29Basic SettingsMiscellaneous1 “View Log Events”Click the “View” button to see the historical log files of the VB-C50i/VB-C50iR’s operation,such as

viiContentsNight Mode Setting Tool ... 4-52External Device Input

3-30

VB Administration ToolsChapter 4 describes practical ways of operating the VB-C50i/VB-C50iR using the VB Administration Tools to createpanoramas, set

4-2Overview of VB Administration ToolsVB Administration Tools comprises “VBAdmin Startup Panel”, “Panorama Creation Tool”, “ViewRestriction Tool”, “Pr

4-3VB Administration ToolsVBAdmin Startup Panel (→ P.4-5)This is the main panel of VB Administration Tools. The tools arestarted up from this panel.In

4-4Overview of VB Administration ToolsLog Viewer (→ P.4-61)This tool enables viewing of operation status logs that are outputto the VB-C50i/VB-C50iR.A

4-5VB Administration ToolsStarting Up VB Administration ToolsTo Start Up...1. Double-click the “VB Admin Tools” desktopicon or select “VB Admin Tools”

4-63. The VBAdmin Startup Panel starts up.The six tools---“Panorama Creation Tool”, “ViewRestriction Tool”, “Preset Setting Tool”, “ScheduleSetting To

4-7VB Administration ToolsPanorama Creation ToolThe Panorama Creation Tool is used to take and create panorama pictures from the VB-C50i/VB-C50iR. Onc

4-8Panorama Creation Tool Display ScreenAn overview of the functions of the GUI displayed when the Panorama Creation Tool starts up isshown below.q “D

4-9VB Administration ToolsTipSince the range that can be captured varies with the type of camera, the displayranges of the panorama pictures are diffe

viiiContentsUsing the Still Picture Recording Functionwith a Predetermined Schedule ... 6-4Sample

4-103. When capturing ends and the picture issatisfactory, click the “OK” button.Panorama creation can be discarded, or the AE lockposition or backlig

4-11VB Administration ToolsReconnectingReconnections are made when a connection with the VB-C50i/VB-C50iR has been cut.To Reconnect...1. Choose “Recon

4-12The View Restriction Setting Tool enables you more visually and easily to set limits on the videowhich can be seen by users. A View Restriction is

4-13VB Administration ToolsView Restriction Tool Display ScreenAn overview of the functions of the GUI displayed when the View Restriction Tool starts

4-14View Restriction Toolt Camera Selection boxSelect the camera to be used to apply view restriction settings.y “Apply the view restriction”View rest

4-15VB Administration ToolsSetting View RestrictionsYou can set up a view restriction by either entering a value in the view restriction setting input

4-16View Restriction ToolRetrieving Values from the Camera Angle of the Admin Viewer andChanging SettingsAdmin Viewer can be used to set the view rest

4-17VB Administration ToolsNoteThe Panorama Preview may be slightly different from the actual picture. After theview restrictions have been set, pleas

4-18Preset Setting ToolThe Preset Setting Tool enables you more visually and easily to set Presets and home position.Presets are set by operating the

4-19VB Administration ToolsPreset Setting ToolPreset Setting Tool Display ScreenThe display screen for the Preset Setting Tool is divided into the “Pr

ixHow to Read This ManualNETWORK CAMERAUser’s ManualVB-C50iPlease read this instruction manual carefully before operation.Be sure to read the “a Safe

4-20Preset Setting Toolt Preset Selection boxSelect the preset to set or “Home”. “Home” is the setting for home position.y “For picture recording only

4-21VB Administration ToolsPreset Setting ToolSetting PresetsYou can set up Presets by either entering a value in the camera parameters or by using th

4-22Retrieving Values from the Camera Angle of the Admin Viewer andChanging SettingsStart up Admin Viewer and set the camera angle as a preset.To Make

4-23VB Administration ToolsTip● You can set a maximum of 20 presets.● Changes in the preset settings are not reflected to the viewer while it is conne

4-24Preset TourA Preset Tour can tour and monitor two or more specified Presets.You can also set Preset Tour with “Presetting Best Shot” in Chapter 3,

4-25VB Administration Toolso Speed (Z)Sets the speed at which the camera moves when zooming, within a range of 1-8. By movingthe slide bar from left t

4-262. Select the preset number you want to add tothe Tour Schedule from the Preset settingarea and click the “Add” button.The preset is registered in

4-27VB Administration ToolsSchedule Setting ToolWith the Schedule Setting Tool, you can set up Timer, Motion Detection, Night Mode, ExternalDevice Inp

4-28Schedule Setting Tool Display Screen (Toolbar)There are two kinds of Schedule settings, Normal Schedule and Special Schedule. The buttons inthe to

4-29VB Administration ToolsNormal ScheduleWith Normal Schedule, you can set up a schedule of one week from Sunday to Saturday. Forexample, during the