Canon Speedlite 600EX-RT Manuel du propriétaire
Naviguer en ligne ou télécharger Manuel du propriétaire pour Flashs d'appareils photo Canon Speedlite 600EX-RT. Canon Speedlite 600EX-RT Owner`s manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
QuickGuide to Speedlite 600EX-RT
Optical Wireless Flash Setup
INTRODUCTION
The Speedlite 600EX-RT allows you to set up multiple
Speedlites which can be wirelessly controlled and syn-
chronized by a single master unit. This QuickGuide will
describe how do this via the traditional Canon “optical”
wireless ash method. Optical wireless ash control
allows you to integrate the 600EX-RT with non-radio com-
patible Speedlite models, even some discontinued ones,
for multiple ash set-ups with full E-TTL auto exposure.
Your setup options include:
• Automatic E-TTL with equal output from all
ring groups
• Automatic Ratio E-TTL with unequal (ratio)
output between ring groups
• Manually-set power output with a different ash
output for each unit or ring group, if desired
A “master” ash unit attached to the camera controls one
or more off-camera “slave units.”
It is also possible to have two or more cameras, each with
a master unit attached, and to switch from one to another
during a wireless ash shooting session. The slave light-
ing setup remains the same. The following Canon units
have master capability with the optical wireless system:
• Speedlites 600EX-RT, 580EX II, 580EX, 550EX,
and newly-introduced 90EX
• Speedlite Transmitter ST-E2
SPEEDLITE 600EX-RT — INITIAL WIRELESS
OPTICAL FLASH SETUP
For this system to work you must rst set the master and
slaves to matching transmission channels. Once you
have done so, any settings you make to the master are
automatically transmitted to the slaves. This eliminates the
need to adjust the slaves individually and manually.
1. Enable optical transmission on the master unit.
Press the Wireless Flash Button until the <OPTICAL
TRANSMISSION> (lightning bolt) icon, in upper-right
corner of 600EX-RT LCD panel, and <MASTER>
appear. The wireless ash button cycle normally is:
Normal ash operation > Radio Master > Radio Slave
> Optical Master > Optical Slave)
2. Enable optical transmission on 600EX-RT
slave unit(s). Press the Wireless Flash Button until
the <OPTICAL TRANSMISSION> icon and <SLAVE>
appear. You can combine one or more 600EX-RTs
as optical-based slave units with any combination of
Speedlite 580EX II, 580EX, 550EX, 430EX II, 430EX,
420EX, 320EX, or 270EX II. Please refer to the
owner’s manual for optical wireless ash setup instruc-
tions for these units.
3. Set the transmission channel. You must set the
master and slave units to the same transmission
channel, otherwise the slave(s) will not re. Four
channels are available. If other photographers are
using Canon optical wireless setups nearby, using
different transmission channels will prevent accidental
triggering of each others’ ash units.
4. To set the Channel on a 600EX-RT master unit:
a) Press Fn button 4 until <MENU 3> appears.
b) Press Fn Button 1 (under the “CH” icon in Menu
c) The channel number highlight will appear imme-
diately below the upper-right lightning bolt icon.
Turn Select Dial to a channel from 1 – 4, then
press the Select/Set Button on the 600EX-RT to
register your choice.
5. To set the Channel on Speedlite 600EX-RTs as
slave unit(s):
a) Press Fn Button 4 until <MENU 2> displays.
b) Press Fn Button 1 (under the “CH” icon in Menu
c) The channel number highlight will appear imme-
diately below the <OPTICAL TRANSMISSION>
icon. Turn selector dial to a channel from 1 – 4,
then press the Select/Set Button to register your
choice.
MASTER FLASH FIRING ON/OFF
You can choose whether master ash ring is ON and
contributes to the ash exposure, or OFF and does not.
When set to OFF, the master ash will still use ash
pulses to control the slaves, however, these ash pulses
will take place before the actual ash exposure, and will
not appear in the nished picture.
1. Press Fn Button 4 until Menu 2 displays.
2. Press Fn Button 1 to set Master Flash Firing to ON or
OFF. (Little beams of light appearing from the small
ash icon indicate Master Flash is ON. When OFF,
the three lines simulating emitted beams disappear.)
WIRELESS E-TTL WITH ALL FLASHES
FIRING AT EQUAL POWER
In this mode all ash units will re with automatic E-TTL
exposure, to produce a standard ash exposure, which
you can adjust with ash exposure compensation on your
camera, as necessary. This mode is best for situations
where you’re trying to evenly light a subject or area, such
as by bouncing several ashes onto a ceiling to evenly
light a large room.
1. Perform the initial ash setup described above.
2. Conrm that master and slave are set to the same
channel.
3. Speedlite 600EX-RTs used as slave units in an even-
power set-up can be assigned to any group — A, B
or C. (Groups D and E are not available in optical
wireless mode.)
Fn Button 1
Wireless
Button
Flash Ready/Test FlashFlash Mode Button
Fn Button 2 Fn Button 3 Fn Button 4
Select Dial
1 2 3
1
2
Résumé du contenu
Page 1 - Optical Wireless Flash Setup
QuickGuide to Speedlite 600EX-RT Optical Wireless Flash Setup INTRODUCTIONThe Speedlite 600EX-RT allows you to set up multiple Speedlites which can be
Page 2
4. Position the camera and slave unit(s) within the correct operating range (10 meters/33 feet indoors), and so that the ash sensors on the front o
Plus de documents pour Flashs d'appareils photo Canon Speedlite 600EX-RT
Canon Speedlite 600EX-RT Manuel d'instructions
(132 pages)
Canon Speedlite 600EX-RT Manuel d'utilisateur
(372 pages)
Produits connexes et manuels pour Flashs d'appareils photo Canon Speedlite 600EX-RT
(2 pages)
(32 pages)
(56 pages)
(172 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels